Taking a slight change of direction in the development of the laser cut models, a friend was looking for a wagon for his Malifaux figures, a troupe of showgirls…
I felt I could put one together for him fairly quickly, we discussed it at out weekly games night, on a Wednesday, and I laser cut on the Friday.
The only parts not laser cut are the two axles, which are 2mm diameter bamboo cotton bud sticks.
After playing around with the various sci-fi fortifications and gantry systems I felt it was about time that I tried something a little more historical.
A friend of mine suggested I have a look at doing a Peel Tower and so after a little time doing some research (i.e. Google-fu) I settled on creating a tower based on the Tower of Hallbar. Not an accurate historical model, but taking the main points of the building and incorporating them into my design.
The following photos are the result. The model is built for 28mm figures and stands around 370mm high.
As part of the project it was important to hide the way the model was constructed, fortunately with the larger stones at the corners, it was possible to create an interlocking design that gave the model great strength as well as reasonably hiding the joins.
The actual stonework on the faces of each wall was created simply by drawing white splodges on a black background to create a very simple stone built effect. This was then repeated over the surface of each piece. The laser engraving of the stone pattern was a very slow process. The whole cutting and engraving took between 3 and 4 hours. If I removed the surface engraving, it would bring it down to around 30 minutes.
In these photos you can see that the roof tiles are actually sloped for each row of tiles. This was done by creating a black to white gradient for each row of tiles. Then using a special 3D setting on the laser cutter that cuts to certain depths depending on the different gradients of black through grey to white.
After I completed the basic tower I decided it would be interesting to a small turret, as seen on several other Peel towers. Now, the problem here is that the laser cutter will only cut flat material. All I could do was cut each ring of bricks as a separate piece and then glue them together. It worked well enough, but I wouldn’t want to have to do it for a turret that was the full height of the building…
Now clearly this model has quite diverse uses, everything from Boarder Reivers games through to fantasy battles and beyond. However the main problem with producing this tower as a saleable item is the time it takes on the machine. The stone effect is very nice, but it simply makes the model uneconomic to produce.
I started a project to make a centre piece for a retro sci-fi wargame sometime early last years. The project was inspired by a plastic domed light fitting that I had had lying around for several years and not really know what to do with.
The project has stalled somewhat at the moment, as I work on other things, but I have recently been working up a few more scenic items for the sci-fi game and so I will probably get around to finishing it off sometime very soon!
As I built the model I photographed the whole process and so here is a run through of the construction.
Cut two 18"x 18" squares of 1" polystyrene which will make up the base of the piece. This is quite a good size for me as I have a series of base boards that are either 18x18 or 18x36, so this will fit in nicely with those.
I have also knocked up a simple plan, just to give myself an idea on how to proceed. The ground floor will be set into the top layer of foam, giving an extra inch of depth for headroom within the dome.
There is a central lift shaft which also supports the first floor control room.
2 sheets of 1" styrofoam, cut 18"x18". The top sheet is marked out with the position of the dome the site of the entry ramp.
This is the base ring for the light fitting.
This is the dome in place.
Now I have to cut the ground floor out of the top sheet of foam and also cut the sloped entry ramp!
I just cut out the top layer of foam using a large hot wire cutter. I set the wire at about a 10 degree angle (just to make it a little more interesting than vertical).
I also cut the entry ramp, which was a little trickier due to the compound angles. So after cutting it I found I had to sand it quite a bit to get it level.
I have now glued the 2 layers of foam together and also glued in the entry ramp. I have used quick drying filler to fill the gaps and left the model to dry overnight.
Then I cut a 80mm diameter postal tube to use as the central lift shaft. Also, using 6mm MDF, I have cut the interior dividing walls. Due to time constraints and also some aesthetic concerns, I have abandoned the central ring corridor.
My projects always tend to evolve as I move them into 3D!
The black rectangle in the lower right of the photo is going to be a freight lift door set into the ground beside the dome, designed to suggest that there are more floors below ground.
This is the upper floor, cut slightly smaller than the outer ring of the building so that the roof dome will locate into the ring. Again 80mm postal tube used for the lift shaft.
Dome in place, checking the fit of the inner floors and postal tubes.
Then I cut the connecting doorways between each of the rooms. Normally on a wargaming model I would simply add door frames onto the wall and paint the wall as the door. But for this project I felt it would be nice to use some slightly thinner material for the doors, adding to the realism. I may also model one or two of the doors in the open position.
Here I am gluing the doors to the inside of the lift shaft. I used some of the same tube to make the doors with. Fortunately the difference in the curve was not enough to cause any problems.
I have been spreading flexible filler on the interior floor polystyrene, in an attempt to disguise the polystyrene beading. A slow process of fill, dry, sand, repeat!
I used a smaller diameter tube for the actual lift cabin. I thin the size will be deceptive, once the only way to see it is through the open doors!
The open atrium area is now cut, also the cream coloured object is part of a yogurt pot that is going to be my main computer bank (very retro).
Added doors to the doorways, glued the main walls in place and added a coat of gray paint.
Here you can see the open lift doors and open door on the lower deck.
I added the dividing wall on the upper deck. This will divide the control roof from Hydroponics.
The gray is darker than I would like. I will probably repaint a good bit lighter. Here you can also see the central lift shaft. I have placed a cone of card into it, and hopefully with some concentric rings and tapering lines painted onto the cone it will give an illusion of a deep shaft.
Looking straight down the shaft!
Close up of the open door on the lower deck. The walls are made of 6mm MDF, the doors from 2mm MDF.
At the moment I am working on strengthening the polystyrene sheets, mounting a card edge to it to match my terrain boards and covering it with papier mache for strength.
Card re-enforcements for the edges of the polystyrene:- 
Papier-mâché used to cover the polystyrene, strengthen the whole board and hide the polystyrene's "bobbly" texture:- 
Adding more paper:- 
That is about where I have gotten to at the moment. I am slowly working on the main entry ramp and door at the moment.
Also I have decided that even though the interior is purely 28mm scale I will keep any obvious scale items off of the outside, so that I can use it for my 15mm sci-fi games as well.
Part 2 of this post will hopefully come along sometime in the next month or two.
Taking my inspiration from the Klendathu base in the movie Starship Troopers, I evolved the ideas I had developed in my the Gantry system to create a temporary military base.
As you can see from the photos, the watch towers are based on a similar design to that used as the look-out post in the gantry system. In fact the whole wall system is based on a scaled up version of the look-out post.
As such the work to develop the walls was very simple. It got more interesting when I moved on to designing the door. I decided I would make it a movable door so that a player could have it open, closed or indeed open and close it during a game (as the patrol makes a dash for the door while the horde of bugs advances on the fort).
The door frame is build up of three layers, the outside, the inside and a spacer layer between. The doors have simple runner attachments at the top that sits over the inside wall. So that the door always closes in the correct position I have included a small stop in the middle at the top of the inside wall, which stops the doors passing the halfway mark.
Most of the fort is built in 3mm MDF, however, the look-out posts on top of the watch towers, the wall walkways and the stairs are 2mm MDF and the spacer in the door wall is 4mm (to allow the door to be painted without jamming).
Just as a little extra, a friend of mine is working on a 28mm scale Ork Gargant and asked me to knock up a circular saw for him, this was the result:-
Note: The minis in these photos are the the 28mm figures I sculpted for Defiance: Vital Ground!
